Trimec ES9000 Pre-Load Electric Strike Trimec ES9000 Pre-Load Electric Strike Trimec ES9000 Pre-Load Electric Strike The ES9000 has been designed to suit the harshest commercial environments, and has the unique feature of the ability to operate with up to 25kg of pre-load pressure on the keeper. Pre-load is a common condition that is caused by pulling on a door before it unlocks, the weight of warped or drooping doors, seals on fire doors, or by differential air pressure created when heating and cooling systems are in use. Standard features include multi voltage 10 - 30Vdc and field changeable settings from fail safe to fail secure. Built to last, this is a premium locking solution that has been tested in excess of 2 million cycles and boasts unique features like no other available on the market today. Key Features Operates under pre load up to 25kg Easy field selectable fail safe/fail secure Multi voltage 10-30Vdc 1300kg holding force 2.5 million cycles endurance rating Latch keeper is significantly quieter in operation Weather resistant Mounting tabs as standard Non handed TRICARE® 5 Year Warranty Australian designed and made Built in Protection Diode Applications High traffic areas Doors subjected to side load (pre load) Fire rated door sets Open in/open out doors Suitable for use with all access control systems Standards and Compliance S3 (Security) Australian Lock Standard (AS4145.2.1993) D3 (Durability) Australian Lock Standard (AS4145.2.1993) Successfully fire rated up to 4hrs on fire door assemblies in accordance with AS1905.1. 2005 (Part 1: Fire resistant door sets) CE Approved C-Tick Certified IP 54 Rating SCEC Approved for Security Level 3 Specification Voltage10 - 30Vdc Current250mA @12Vdc - 130mA @24Vdc SolenoidsSolenoid rated for continuous use Electrical protectionPolarity and back EMF protected MonitoringSolenoid Monitor - 1 amp NO/NC microswitchDoor / Latch Monitor - 1 amp NO/NC microswitch Holding force1300kg static strength rating Endurance1,200,000 cycles endurance rating @ 25kg pre-load2,500,000 cycles general durability without pre-load conditions LatchingSuitable for 15mm latch with 3mm door gap EnvironmentOperational temperature range - 20C to +60C BodySolid Stainless Steel Construction KeeperStainless Steel Specification StatementThe electric strike should be fully monitored and have independent door / latch and solenoid monitor switches. Holding force for the strike should be not less than 1300kg. Where Power to Lock and Power to Open functions may be required in the same building, a single electric strike should be interchangeable from either fail safe or fail secure from the rear of the strike. The electric strike should not consume current greater than 250mA @ 12Vdc and have a solenoid rated for continuous use. A fire rating not less than 4 hours is required where applicable. The strike must be capable of operating with up to 25kg of pre-load pressure applied to the keeper, be tested to 2.5 million operations and carry a minimum warranty of 5 years. Dimensions Close Documents | Downloads ES9000 Installation Instructions.pdf (.pdf, 347 kB) Trimec Electric Strikes Catalogue Section.pdf (.pdf, 1.6 MB) Close Ordering Ordering Information Description Part Number ES9000 Pre - Load Multi Function Strike with Standard 15.5mm Lip 119001-000 ES9000 Pre - Load Multi Function Strike - No Lip 119001-010 ES9000 Pre - Load Multi Function Strike - 8mm Lip 119001-020 ES9000 Pre - Load Multi Function Strike - with Extension Lip Holes 119001-060 25mm Lip Extension (40.5mm Total) to suit 119001-060 220200-505 50mm Lip Extension (65.5mm Total) to suit 119001-060 220200-506 75mm Lip Extension (90.5mm Total) to suit 119001-060 220200-507 Note: All ES9000 series electric strikes are supplied in Fail Safe configuration. Close ES9000 Product Testing Trimec ES2000 Series Monitored Electric StrikeFail safe/fail secure changeable on site. Trimec ES150 Series Surface Mounted Electric StrikeFail safe/fail secure changeable on site. Trimec ES2600 Series Monitored Electric StrikeFail safe/fail secure changeable on site.